Showing all 4 results

  • Sheenlac Xperia 2K Epoxy Insulator

    ,
    ₹920.00

    Sheenlac Xperia 2K Epoxy Insulator is a tough, transparent clear coating recommended to apply on
    oil rich wood. This clear coat acts as a barrier coat on bare wood and preventing the oil leaching from
    wood. It is ideal to use as a barrier coat for Polyurethane, Polyester, Melamine and Acrylic topcoat
    clears.

    Select options

  • Paint Remover

    Solvent gazed wax type stripper, acts on all types of paint films.

    ,
    ₹191.00 – ₹351.00

    Sheenlac Paint Remover is a solvent-based wax type stripper, acting on all types of paint films even on vertical substrate.

    Direction of Use:

    Make deep cuts on the old paint surface using a sharp edge knife / putty blade. Shake the content well before use. No dilution is required. Apply the paint remover by brush as a thin layer and allow it to react for 10-15 mins. Use a putty knife to remove the lifted area and use mild force to remove the loose paint. Repeat the procedure till you get to the bare substrate. After thorough removal of paint, use plenty of water and soap to rinse off and clean. If used on wood, wipe-off with cloth, soaked in Sheenlac Enamel/ N.C Thinner D-13x

    Select options

  • SHEENLAC WATER BASED PARQUET FLOOR POLISH

    Sheenlac Exterior Heavy Duty clear parquet polish is composed of a water based dispersion of cross-linking polyurethane copolymer with surfactants, waxes, and rheology modifying agents. An ultra-hard, high-quality polish with a semi-gloss or matt finish that dries to a crystal clear film is recommended for both interior and exterior surfaces that require a high level of protection from high wear, such areas gymnasiums, dance floors, and public halls. WB parquet polish is ideal for use on: Wood, stone, brick, slate, and cork tiles, to give a hard clear protective coating with a high degree of chemical and abrasion resistance.

    , , ,
    ₹826.00

    Sheenlac Exterior Heavy Duty clear parquet polish is composed of a water based dispersion of cross-linking polyurethane
    copolymer with surfactants, waxes, and rheology modifying agents.

    An ultra-hard, high-quality polish with a semi-gloss or matt finish that dries to a crystal clear film recommended for both interior and exterior surfaces where it requires a high level of protection from high wear such areas as gymnasiums, dance floors, andpublic halls.
    WB parquet polish is ideal for use on Wood, stone, brick, slate, and cork tiles, to give a hard clear protective coating with a high
    degree of chemical and abrasion resistance.

    Application

    Sheenlac WB Parquet polish can be applied by brush, spray or roller.

    Porous surfaces should be primed with WB Parquet polish after
    diluting it with 40–50% water.

    Sand the surface to remove any raised grain and wipe out the dust.

    If required, stain the wood using Sheenlac wood stain after diluting it
    with 20–40% water. Allow it to dry for 2 hours.

    Further 2 or 3 coats of parquet polish is required for better finish and
    performance. Dilute the polish with 10–20% water for roller finish. 30-40% for spray or brush use.

    Light sanding in between coats may be necessary if there is any
    raising the grain. Use #320 or 400 emery for this purpose.

    Allow 2 hours in between coats and 16 hours after final coat before full use.

    Do not use in temperatures below 5 °C / 40°F or in very high
    humidity.

    Lower temperatures will slow the final cure time.

    For a high level of protection and stain resistance in matt
    finish, we recommend applying 2 coats of semi-glossy finish, then 1 coat of matt finish.

    Select options

  • PU Thinner D-67

    Solvent gazed wax type stripper, acts on all types of paint films.

    ,
    ₹267.00

    Sheenlac Polyurethane Thinner D-67 is a blend of aromatic hydrocarbon, ester and ketone solvents suitable for dilution of solvent based polyurethane sealer, primer, clear and pigmented topcoat to obtain proper paint consistency for application.

    Recommended Use:

    Suitable for dilution of all types of solvent based polyurethane sealer, primer, clear and pigmented topcoat. It is also used for cleaning of tools immediately after application of polyurethane paints.

    Select options