Out of Stock

Paint Remover

191.00351.00

Sheenlac Paint Remover is a solvent-based wax type stripper, acting on all types of paint films even on vertical substrate.

Direction of Use:

Make deep cuts on the old paint surface using a sharp edge knife / putty blade. Shake the content well before use. No dilution is required. Apply the paint remover by brush as a thin layer and allow it to react for 10-15 mins. Use a putty knife to remove the lifted area and use mild force to remove the loose paint. Repeat the procedure till you get to the bare substrate. After thorough removal of paint, use plenty of water and soap to rinse off and clean. If used on wood, wipe-off with cloth, soaked in Sheenlac Enamel/ N.C Thinner D-13x

Reviews

There are no reviews yet.

Be the first to review “Paint Remover”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsPaint Remover removeJensolin Primer removeOpulence Premium 2K Interior PU removeWater Based Timber Filler removeWater-based Impregnation Clear removeWater Based 1K Exterior Wood Coating remove
Image
SKU
Rating
Price191.00351.00139.004,664.00962.003,827.00 150.00180.00350.00330.0016,014.00
Stock

Out of stock

AvailabilityOut of stock
Add to cart

Select options

Select options

Select options

Select options

Select options

Select options

DescriptionSheenlac Paint Remover is a solvent-based wax type stripper, acting on all types of paint films even on vertical substrate. Direction of Use: Make deep cuts on the old paint surface using a sharp edge knife / putty blade. Shake the content well before use. No dilution is required. Apply the paint remover by brush as a thin layer and allow it to react for 10-15 mins. Use a putty knife to remove the lifted area and use mild force to remove the loose paint. Repeat the procedure till you get to the bare substrate. After thorough removal of paint, use plenty of water and soap to rinse off and clean. If used on wood, wipe-off with cloth, soaked in Sheenlac Enamel/ N.C Thinner D-13xJensolin Pink Primer, a solvent based undercoat promises perfect surface preparation for new and unpainted wooden surfaces. The product hides existing surface stains and discoloration. Glossy, Semi-glossy and flat oil finishes can be applied directly onto the surface, coated with this primer. It is specially formulated to provide an excellent balance between filling, penetration and adhesion to wood.Opulence Interior PU is an acrylic based 2 pack polyurethane clear wood coating. It forms and tough, non-yellowing film that accentuate the nature beauty of interior wooden surface. Resilient and durable for years Great balance of hardness and flexibility Excellent chemical and mechanical resistance.
  • Resilient and durable for years
  • Great balance of hardness and flexibility
  • Excellent chemical and mechanical resistance
Water Based Timber Filler is an alkyd based, semi solid paste that fills minor imperfections on the surface and improves top coat adhesion and appearance. RECOMMENDED USE: Water based timber filler is mostly used on wooden surfaces.Sheenlac Water based Impregnation Clear is a Transparent Coating used on saturated, soaked or weathered wood. RECOMMENDED USE: Water based Impregnation clear is mostly used on wooden surfaces that have undergone.Sheenlac Water based PU exterior wood coating is an 1K PU clear designed to provide excellent protection for all types of outdoor wood projects from UV rays, weathering, temperature changes and humidity.
  • Available in 30 and 60 gloss levels
  • Durable UV protection for Wood
  • Protection from temperature changes and humidity
Content

Color

White & Colors

Gloss / sheen

85 – 95 Gloss Unit at 60° Gloss Head

Drying Temperature

25°C / 50% RH

 

RECOMMENDED USE: Brolac Hi- Gloss Polyurethane Enamel can be used on metal, masonry and wooden surfaces.

Product benefits:
  1. Hi-gloss finish
  2. Recommended as a top-coat for mild corrosive environment over suitable primers
  3.  Excellent levelling and application properties
100-110* sq. ft. / litre for 1 coat finish under normal conditions *Actual coverage may vary due to factors such as method and condition of application, surface roughness and porosity and weather conditions.
  1. Ensure that the surface is free from dirt, grease, rust and moisture.
  2. Sand the surface using Emery Paper 180 to remove loosely bound particles, rust, peeling or flaking paint, etc.
  3.  Wipe the surface clean.
PRIMING Ferrous Metal Surface: Apply 1-2 coats of J&N Superior Red Oxide Primer on the metal surface by thinning (If necessary). Allow drying for 8-10 hrs after each coat. Non-Ferrous Metal Surface: Apply 1-2 coats of J&N Zinc Primer Yellow on the metal surface, by thinning it with J&N GP Thinner, if necessary. Let it dry for 5-6 hrs. Wooden Surface: Apply first coat of Jensolin Pink/White Primer on the wooden surface by thinning with J&N GP thinner (if required). Let it dry for 8-10 hrs. Use suitable putty to fill minor cracks, dents or holes. After drying, use Emery Paper 180 to sand the surface. Apply another coat of J&N Pink/White Primer. Allow it to dry for 8-10 hrs. Masonry Surface: Apply first coat of Jensolin Pink/White Primer on the surface by thinning with J&N GP thinner (if necessary). Let it dry for 8-10 hrs.
Apply two coats of Brolac Hi- Gloss Polyurethane Enamel, after thorough stirring and diluting (if required). Maintain an interval of 6-8 hrs between successive coats.
  1. Do not over thin the paint above recommended dilution levels.
  2. Stir the paint properly, before use.
  3.  Seal the container, when not in use.
  4.  Clean the application tools immediately after use.
  1. Ensure drying time of a week, before cleaning.
  2. Remove stains using clean sponge and mild soap solution
  3.  Wipe clean.
Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage Shelf Life: One year from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

Gloss level @ 60˚

Gloss: 90 | Matt: 15-20

Drying Temperature

@30˚ C and 60% RH

Application method

Spray

Tack free

3 Hours

Surface Dry

10 - 15 minutes

Overcoat interval

8 -12 Hours


RECOMMENDED USE: Aspire interior is the perfect choice for dark colored commercial and household furniture, high end kitchen cabinetry, bathroom vanities, doors, Table tops, Bar tops, music instruments, sports goods, and other interior wood surfaces that require a hard durable finish. Not recommend on light / pale colored wood.

PRODUCT BENEFITS:

DURABllllY: It forms a tough yet flexible film which resists cracking even at curved edges. Further its special chemistry imparts it good heat, stain and chemical resistance properties.

SUPERIOR GLOSS RETENTION: Opulence Interior Forms a clear non yellowing coat on your wooden interiors which accentuates their beauty for a long duration.

RESISTANCE: Opulence has high gloss, stain and heat resistance when compared to conventional wood finishes.

FllM FLEXIBILITY: Opulence forms and extremely flexible film on the surface of wood which resists cracking even on the curved edges.


*Recoat and drying period may vary under different conditions
SURFACE PREPARATION: All wood surfaces must be clean, firm and dry. Remove any oil, grease, mortar droppings, etc.

NEW WOOD: Sand in the direction of the grain, to a smooth finish with 150 followed by 220 grit paper. Remove dust with a damp cloth.

PREVIOUSLY VARNISHED WOOD IN GOOD CONDITION: Sand to obtain a smooth surface using 150 grit emery paper. Remove all sanding dust using a vacuum or cloth dampened with mineral spirits.

PREVIOUSLY VARNISHED WOOD IN POOR CONDITION: Strip completely by deep. sanding or by using Sheen lac Paint Remover. Rinse thoroughly with clean water. Deep sand to until there is no evidence of any residue. Remove dust with a damp cloth.

WOOD PREVIOUSLY COATED WITH WAX SEALER/OIL BASED WOOD PRESERVATIVE: Mechanically sand until there is no evidence of residue. Remove dust with a damp cloth.

PREVIOUSLY PAINTED WOOD: Strip old paint by deep sanding or by using Sheenlac Paint Remover. Rinse thoroughly with clean water. Sand bare wood to a smooth finish. Remove dust with a damp cloth.

DISCOLOURED OR WEATHERED WOOD: Remove discoloured or weathered layer by sanding with 100 grit paper and treat it with Sheenlac WB Impregnation clear. Dry it for 2 hrs and sand to remove the grain rise with #220 grit paper. Remove dust with a dry cloth followed by Wood stain colour, to prevent further discoloration and restore the natural colour.

FILLER: If required use Sheenlac NC or Oil based Wood filler. Remove the excess using 220 grit Emery paper and wipe with dry cloth.

STAIN THE WOOD: Adding stain to bare or stripped wood can both change the color and highlight the gtain pattern of any interior wood but this is an optional. Apply Sheenlac SB Wood stains directly on wood or can be mixed @10% max with base coat sealer to produce stained finishes.
  • Always keep paint out of reach of children.
  •  Ehsure good ventilation during application and drying.
  •  If accidental contact with skin should occur, wash immediately with soap and water.
  •  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
  •  Harmful if swallowed. Seek medical attention and do not induce vomiting.
  •  Do not smoke while painting.
  •  Flammable. Store in a cool dry place away from heat and sparks.
  •  Refer to Material Safety Data Sheet for compiete information

Drying Temperature

@30˚ C and 60% RH

Application method

Padding

Flash point

Above at 12° C

Touch Dry

2 minutes

Re-coating Interval

30 minutes

RECOMMENDED USE: Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

RECOMMENDED USE: Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

*Recoat and drying period may vary under different conditions
100-120 Sq ft / L / Coat *Actual coverage may vary based on the type of wood used and the application methodology.
Reveals the highlights of well grained timber. Good water resistance property. 100% Lead free. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past.
BARE WOOD: First, seal with one or two coats of NC wood filler and then apply four to five coats of Sheenlac Wood Polish. PREVIOUSLY VARNISHED WOOD (IN GOOD CONDITION): First, seal with one coat of NC sanding sealer and then apply three or four coats of Sheenlac Wood Polish.
  1. Always keep paint out of reach of children.
  2. Ensure good ventilation during application and drying.
  3. If accidental contact with skin should occur, wash immediately with soap and water.
  4. Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
  5. Harmful if swallowed. Seek medical attention and do not induce vomiting.
  6. Do not smoke while painting.
  7. Flammable. Store in a cool dry place away from heat and sparks.
  8. Refer to Material Safety Data Sheet for complete information.
Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage Shelf Life: 2 Years from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.
Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

Drying Temperature

@30˚ C and 60% RH

Application method

Padding

Flash point

Above at 12° C

Touch Dry

2 minutes

Re-coating Interval

30 minutes

RECOMMENDED USE: Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

RECOMMENDED USE: Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

*Recoat and drying period may vary under different conditions
100-120 Sq ft / L / Coat *Actual coverage may vary based on the type of wood used and the application methodology.
Reveals the highlights of well grained timber. Good water resistance property. 100% Lead free. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past.
BARE WOOD: First, seal with one or two coats of NC wood filler and then apply four to five coats of Sheenlac Wood Polish. PREVIOUSLY VARNISHED WOOD (IN GOOD CONDITION): First, seal with one coat of NC sanding sealer and then apply three or four coats of Sheenlac Wood Polish.
  1. Always keep paint out of reach of children.
  2. Ensure good ventilation during application and drying.
  3. If accidental contact with skin should occur, wash immediately with soap and water.
  4. Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
  5. Harmful if swallowed. Seek medical attention and do not induce vomiting.
  6. Do not smoke while painting.
  7. Flammable. Store in a cool dry place away from heat and sparks.
  8. Refer to Material Safety Data Sheet for complete information.
Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage Shelf Life: 2 Years from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.
Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

Gloss level @ 60˚

Gloss: 90 | Matt: 15-20

Drying Temperature

@30˚ C and 60% RH

Application method

Spray

 

Tack free

3 Hours

Surface Dry

10 - 15 minutes

Overcoat interval

8 -12 Hours



RECOMMENDED USE: Aspire interior is the perfect choice for dark colored commercial and household furniture, high end kitchen cabinetry, bathroom vanities, doors, Table tops, Bar tops, music instruments, sports goods, and other interior wood surfaces that require a hard durable finish. Not recommend on light / pale colored wood.


*Recoat and drying period may vary under different conditions
Sq ft / L / Coat

*Performance may vary due to factors such as method of application, surface roughness and porosity.
  1. Alkali Resistant
  2. Excellent Sealing Properties
  3.  Excellent Coverage
  4.  Quick Drying
  5.  Excellent Top coat Holding
  1. Apply MP-300 plastic primer on plastic substrate
  2. Apply suitable putty wherever required to fill the undulation / dent to make the surface flat and apply BP-2400 1 K primer grey / BP-5000 2 K primer grey
  3.  Apply Bodyian base coat colour and provide flash off time of 10 – 15 mins
  4.  Apply suitable Bodyian clear coat as per suggested ratio
  1. Always keep paint out of reach of children.
  2. Ensure good ventilation during application and drying.
  3.  If accidental contact with skin should occur, wash immediately with soap and water.
  4.  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
  5.  Harmful if swallowed. Seek medical attention and do not induce vomiting.
  6.  Do not smoke while painting.
  7.  Flammable. Store in a cool dry place away from heat and sparks.
  8.  Refer to Material Safety Data Sheet for complete information.
Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage

Shelf Life: 24 months from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.
Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Size

500 ml, 1 Ltr

Size

500 ml, 1 Ltr, 4 Ltr, 20 Ltr

Finish

PINK PRIMER, WHITE PRIMER

Size

1 Ltr, 4 Ltr

Finish

Glossy, Matt, Sealer (Base Coat)

Size

1 Kg

Finish

Mahogany, Natural, Oak, Teak, Walnut

Size

500 ml, 1 Ltr

Size

500 ml, 1 Ltr, 20 Ltr

Finish

Matt, Satin, Semi Glossy