Water-based Impregnation Clear

100-120 Sq ft / L / Coat *Actual coverage may vary based on the type of wood used and the application methodology.

Reveals the highlights of well grained timber. Good water resistance property. 100% Lead free. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past.

BARE WOOD: First, seal with one or two coats of NC wood filler and then apply four to five coats of Sheenlac Wood Polish. PREVIOUSLY VARNISHED WOOD (IN GOOD CONDITION): First, seal with one coat of NC sanding sealer and then apply three or four coats of Sheenlac Wood Polish.

1. Always keep paint out of reach of children.
2. Ensure good ventilation during application and drying.
3. If accidental contact with skin should occur, wash immediately with soap and water.
4. Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
5. Harmful if swallowed. Seek medical attention and do not induce vomiting.
6. Do not smoke while painting.
7. Flammable. Store in a cool dry place away from heat and sparks.
8. Refer to Material Safety Data Sheet for complete information.

Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage Shelf Life: 2 Years from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

Wood polish is suitable for use on all types of soft and hardwood timber structures which is in less critical areas (where heat, water, scratch, stain and mar resistance is not critical). It can be used on all bamboo, cane and wooden surfaces including furniture, door, window, frame structures, stair rails and other professional work. Not recommended for exterior use due to its limited UV Resistance.

Sq ft / L / Coat

*Performance may vary due to factors such as method of application, surface roughness and porosity.

1. Alkali Resistant
2. Excellent Sealing Properties
3.  Excellent Coverage
4.  Quick Drying
5.  Excellent Top coat Holding

1. Apply MP-300 plastic primer on plastic substrate
2. Apply suitable putty wherever required to fill the undulation / dent to make the surface flat and apply BP-2400 1 K primer grey / BP-5000 2 K primer grey
3.  Apply Bodyian base coat colour and provide flash off time of 10 – 15 mins
4.  Apply suitable Bodyian clear coat as per suggested ratio

1. Always keep paint out of reach of children.
2. Ensure good ventilation during application and drying.
3.  If accidental contact with skin should occur, wash immediately with soap and water.
4.  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
5.  Harmful if swallowed. Seek medical attention and do not induce vomiting.
6.  Do not smoke while painting.
7.  Flammable. Store in a cool dry place away from heat and sparks.
8.  Refer to Material Safety Data Sheet for complete information.

Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage

Shelf Life: 24 months from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

Sq ft / L / Coat

*Performance may vary due to factors such as method of application, surface roughness and porosity.

1. Alkali Resistant
2. Excellent Sealing Properties
3.  Excellent Coverage
4.  Quick Drying
5.  Excellent Top coat Holding

1. Apply MP-300 plastic primer on plastic substrate
2. Apply suitable putty wherever required to fill the undulation / dent to make the surface flat and apply BP-2400 1 K primer grey / BP-5000 2 K primer grey
3.  Apply Bodyian base coat colour and provide flash off time of 10 – 15 mins
4.  Apply suitable Bodyian clear coat as per suggested ratio

1. Always keep paint out of reach of children.
2. Ensure good ventilation during application and drying.
3.  If accidental contact with skin should occur, wash immediately with soap and water.
4.  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
5.  Harmful if swallowed. Seek medical attention and do not induce vomiting.
6.  Do not smoke while painting.
7.  Flammable. Store in a cool dry place away from heat and sparks.
8.  Refer to Material Safety Data Sheet for complete information.

Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage

Shelf Life: 24 months from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

Sq ft / L / Coat

*Performance may vary due to factors such as method of application, surface roughness and porosity.

1. Alkali Resistant
2. Excellent Sealing Properties
3.  Excellent Coverage
4.  Quick Drying
5.  Excellent Top coat Holding

1. Apply MP-300 plastic primer on plastic substrate
2. Apply suitable putty wherever required to fill the undulation / dent to make the surface flat and apply BP-2400 1 K primer grey / BP-5000 2 K primer grey
3.  Apply Bodyian base coat colour and provide flash off time of 10 – 15 mins
4.  Apply suitable Bodyian clear coat as per suggested ratio

1. Always keep paint out of reach of children.
2. Ensure good ventilation during application and drying.
3.  If accidental contact with skin should occur, wash immediately with soap and water.
4.  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
5.  Harmful if swallowed. Seek medical attention and do not induce vomiting.
6.  Do not smoke while painting.
7.  Flammable. Store in a cool dry place away from heat and sparks.
8.  Refer to Material Safety Data Sheet for complete information.

Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage

Shelf Life: 24 months from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

WRITE-OFF is a semi gloss coating and the undulations and imperfections of the surface can get magnified if the surface is not smoothened out.

• Fill the holes and cracks, straighten the undulations and sand the rough surfaces before application.
•  Frame the selected area to be painted using suitable painters tape.
•  For concrete wall use JN wr CEMENT PRIMER and for metal use Jensolin White Primer.
•  The primer surface should be allowed to dry for minimum of 24 hours and should free from all contaminations.
•  over the Primer apply recommended coloured or white wall coating emulsion.
•  Apply the Write-off over the prepared colour/ white emulsion. High quality of colour/ white emulsion paint with rich sheen is recommended for better performance of Write Off. Coat by roller/ spray. Apply one more coat as appropriate.

New concrete, masonry or plaster: Allow the newly constructed cement surface to cure minimum for 30 days prior to application of coating. Always ensure the wall to be painted is dry and devoid of any loosely adhering cement.

• Stir the base thoroughly. Mix hardener gradually into the base under continuous stirring as per the mixing ratios. Use potable water for thinning and don't over thin the paint more than the recommended levels
•  Apply a first coat of Write-off, by diluting with 10-20% water. Allow it to dry for minimum 7-8 hours (25° C / 50% RH)
•  Apply further coat of WRITE OFF to achieve the desire opacity as well as finish, by diluting with 10-20% water using standard roller or spray. The best finish is obtained when weare apply using air assisted spray technique.

• After application the applied surface needs to be left in ambient conditions for 3 days before it can be used as an erasable surface.
•  Use duster or a lint free cloth to wipe and avoid using any abrasive material or solvent wiping to erase.
•  If after erasing retain "ghost marks", use our Write off cleaning solution to remove the marks.
•  Use Write off cleaning solution every 15 days and change the duster as appropriate period for better erasing.

Storage and Transportation:

Do not store or transport the containers under direct sunlight or at elevated temperatures. Store the container in an upright position in order to avoid any leakage or damage

Shelf Life:

One year from the date of manufacturing in original tightly closed containers stored away from direct sunlight and excessive heat.

Pack Sizes:

White: 500ml, 1 L. Other pack sizes available on request.

1. After application the applied surface needs to be left in ambient conditions for 3 days before it can be used as an erasable surface.
2. Use duster or a lint free cloth to wipe and avoid using any abrasive material or solvent wiping to erase.
3.  If after erasing retain "ghost marks", use our Write off cleaning solution to remove the marks.
4.  Use Write off cleaning solution every 15 days and change the duster as appropriate period for better erasing.

• Keep containers upright, tightly closed in a cool, dry, well ventilated location
•  Keep opened containers closed and tightly closed when not in use
•  Store away from heat source, direct sunlight and other flammable materials
• Keep out of reach of children & pets. Do not store near food, drinks or animal feed
• Do not mix with incompatible materials
• Wear appropriate body, eye and respiratory protection equipment
• Work in a well ventilated area. Do not breathe vapour or sprayed contents
• Skin contact may cause irritation. In case of skin contact wash immediately with water
• In case of eye contact, wash immediately with plenty of water and seek immediate medical attention
• Dispose any spilled or unused paint, containers through appropriate disposal agency
• Do not dispose spillages or unused paint in drain ,water bodies and landfill

SURFACE PREPARATION: All wood surfaces must be clean, firm and dry. Remove any oil, grease, mortar droppings, etc.

NEW WOOD: Sand in the direction of the grain, to a smooth finish with 150 followed by 220 grit paper. Remove dust with a damp cloth.

PREVIOUSLY VARNISHED WOOD IN GOOD CONDITION: Sand to obtain a smooth surface using 150 grit emery paper. Remove all sanding dust using a vacuum or cloth dampened with mineral spirits.

PREVIOUSLY VARNISHED WOOD IN POOR CONDITION: Strip completely by deep. sanding or by using Sheen lac Paint Remover. Rinse thoroughly with clean water. Deep sand to until there is no evidence of any residue. Remove dust with a damp cloth.

WOOD PREVIOUSLY COATED WITH WAX SEALER/OIL BASED WOOD PRESERVATIVE: Mechanically sand until there is no evidence of residue. Remove dust with a damp cloth.

PREVIOUSLY PAINTED WOOD: Strip old paint by deep sanding or by using Sheenlac Paint Remover. Rinse thoroughly with clean water. Sand bare wood to a smooth finish. Remove dust with a damp cloth.

DISCOLOURED OR WEATHERED WOOD: Remove discoloured or weathered layer by sanding with 100 grit paper and treat it with Sheenlac WB Impregnation clear. Dry it for 2 hrs and sand to remove the grain rise with #220 grit paper. Remove dust with a dry cloth followed by Wood stain colour, to prevent further discoloration and restore the natural colour.

FILLER: If required use Sheenlac NC or Oil based Wood filler. Remove the excess using 220 grit Emery paper and wipe with dry cloth.

STAIN THE WOOD: Adding stain to bare or stripped wood can both change the color and highlight the gtain pattern of any interior wood but this is an optional. Apply Sheenlac SB Wood stains directly on wood or can be mixed @10% max with base coat sealer to produce stained finishes.

• Always keep paint out of reach of children.
•  Ehsure good ventilation during application and drying.
•  If accidental contact with skin should occur, wash immediately with soap and water.
•  Take care to avoid contact with the eyes. In case of contact, immediately rinse the eyes with plenty of water and seek medical attention.
•  Harmful if swallowed. Seek medical attention and do not induce vomiting.
•  Do not smoke while painting.
•  Flammable. Store in a cool dry place away from heat and sparks.
•  Refer to Material Safety Data Sheet for compiete information